Xylem IM244R04 SPD Plus Variable Speed Pump Control Manuale Utente Scaricare il pdf (Pagina 2)

SPD PLUS

Centrifugal Pump Controller

Quick Start Guide

Overview

The installation of the SPD PLUS adjust-able

speed drive follows the outline below.

Task

PREPARE for installation

UNPACK the drive

PREPARE mounting location

REMOVE the front cover

MOUNT the drive

INSTALL wiring

CHECK installation

REINSTALL the cover

APPLY power

START-UP Assistant

Application

This guide provides a quick reference for

installing SPD PLUS drives having a standard

enclosure (NEMA 1).

NOTE: This guide does not provide detailed

installation, safety or operational instruc-

tions. See the Installation Operation Manual

for complete information.

Prepare for Installation

WARNING! The Aquavar should ONLY

be installed by a qualied electrician.

Check

• Motor Compatibility – Motor type, nominal current,

frequency and voltage range must match drive

specifications (3 phase motor only).

• Suitable Environment – Drive requires heated,

indoor controlled environment that is suitable for

the selected enclosure below 122º F (50º C).

• Wiring – Follow local codes for wiring and fusing

requirements. Refer to NEC, Local, State or Munici-

pal codes.

Refer to the Installation Operation Manual and

confirm that all preparations are complete.

Tools Required

Screwdrivers, wire stripper, tape measure, mount-

ing screws or bolts, and drill.

Use the following chart to interpret the type code

found on the drive label.

Collect Motor Data

Collect the following data from the motor nameplate

plate for later use in the Aquavar startup:

• Voltage

______________________________

• Nominal Motor Current

_______________

• Nominal Frequency

___________________

• Nominal Speed

______________________

• Nominal Power

_______________________

Unpack the Drive

NOTE: Lift the SPD PLUS by its chassis and not

by its cover.

1. Unpack the drive.

2. Check for any damage and notify the

shipper immediately if damaged com-

ponents are found.

3. Check the contents against the order

and the shipping label to verify that all

parts have been received.

Prepare the Mounting Location

The drive requires a smooth,

vertical, solid surface, free from

heat and moisture, with free

space for air ow – 200 mm (8

in.) above and below, and 25

mm (1 in.) around the sides of

the drive.

1. Mark the mounting

points.

2. Drill the mounting holes.

Remove the Front Cover

1. Remove the control panel

(display), if attached.

2. Loosen the

captive screw

the top.

3. Pull near the

top to remove

the cover.

Mount the Drive

1. Position the

SPD PLUS and use

screws or bolts to

securely tighten all

four corners.

2. Attach a warning

sticker in the

appropriate lan-

guage on the inside

plastic shell.

Install the Wiring (copper only)

1. Install thin-wall conduit clamps (not

supplied) in the conduit/gland box.

2. Install conduit/gland box.

Wiring Power

1. Connect conduit runs to box.

2. Route input power and motor

wiring through conduits.

X0002

SPD 4 0600 N1

Single Pump Drive

Voltage

2 – 230 Volt 4 – 460 Volt 5 – 575 Volt

Nominal Horsepower

0400 = 40 HP 0500 = 50 HP 0600 = 60 HP

0750 = 75 HP 1000 = 100 HP

Enclosure and Filter Options

Blank = NEMA 3R, no lter N1 = NEMA 1, no lter

F = NEMA 3R, with lter

NOTE: HP rating is for reference only, and is based on 3Ø input power.

3. Strip wires.

4. Connect power, motor and

ground wires to the drive terminals.

See “Power Supply and Wiring”

in the instruction manual.

Frame Sizes R1…R4

* Single phase input power must use U1, W1

and PE for wiring.

WARNING! For oating networks

remove screws at EM1 and EM3 on

Frame Sizes R1…R4.

Frame Size R5

Frame Size R6

WARNING!

For oating net-

works remove

screws at

F1 and F2

on Frame

Sizes R5 or R6.

1 2 3 4 5 6 7 ... 35 36

Commenti su questo manuale

Nessun commento

Xylem IM244R04 SPD Plus Variable Speed Pump Control Manuale Utente Pagina 2

Commenti su questo manuale

Prodotti e manuali riguardandi Pompe Xylem IM244R04 SPD Plus Variable Speed Pump Control